Hey Bob, we can get your 2023 Hyundai Santa Fe hybrid set up with a trailer wiring harness, and there are a couple options depending on if you need a 4-way or a 7-way. If you're using a brake controller you'll need the 7-way, otherwise if you just need the harness to activate the trailer's lighting and nothing else, you'll just need the 4-way. Here are your options:
- 4-Way Connector: Curt T-Connector Vehicle Wiring Harness # CU94FR
- 7-Way Connector: Curt T-Connector Vehicle Wiring Harness... view full answer...
A platform-style bike rack is a great choice to carry your bikes. The padded hooks are adjustable on the upright mast to accommodate bikes of different sizes. However, due to the severe dip in the frame bar of cruiser bikes, like you referenced, using a bike adapter bar to secure the hook of the bike rack is a good idea.
I recommend using the Swagman Easy-out Women's and Alternative Frame Bike Adapter # 64005. The bike adapter bar secures at the handle bar post and the seat post to provide... view full answer...
I checked with Yakima and the replacement brackets alone - without the hardware - is not available as a replacement part. So you will get the brackets and the hardware when ordering the Replacement Mounting Brackets for Yakima RoadShower # Y8881255.
We can't remove pieces of a kit and retroactively apply a discount, you'll need to get the brackets with the hardware. view full answer...
The Kat's Heaters Custom Fit Engine Block Heater, part # KH11479, is not designed with a thermostat.
There would be power to the heater when it is plugged in and it does not have an auto shut-off. view full answer...
There are three wiring harnesses available for the 2009 Santa Fe. If your vehicle is equipped with the tow package, use part # 118258 that would plug into the the existing factory connector under the vehicle.
If your Santa Fe was not equipped with the tow package, you can use either the Tow Ready # 118415 or the Curt # C56078. Either of these harnesses would connect inline with the factory harness behind each tail light assembly.
I will link you to install instructions, as well as an... view full answer...
The Hollywood Racks Trail Rider 2 Bike Platform Rack # HR200Z is able to accommodate most bikes that have an alternative frame, like you often see on women's bikes.
That being said, depending on the design of your specific bike frame, and how slanted cross tube is, using an adapter bar like # HRBA-PRO may not be a bad idea so your bike is as secure as possible when carrying it. view full answer...
The Curt T-Connector Vehicle Wiring Harness for Factory Tow Package - 7-Way Trailer Connector # C68JR does fit the 2023 Hyundai Santa Fe.
The reason we have it in our fit guide but Curt does not is because one of our installers put this on a Santa Fe so they directly tested it, which is where our info comes from. view full answer...
I have a really great Class III hitch option made by the same company as the Hidden Hitch you mentioned but the 87544 does not fit your vehicle so you'd instead want the Draw Tite part # 75471 which is a confirmed fit for you vehicle.
I attached an install video for this hitch as well as a picture that shows what it looks like installed as well. view full answer...
With the etrailer Trailer Hitch Receiver # e98843 installed on a 2019 Hyundai Santa Fe in our Shop we measured the hitch pin center hole to be 4" from the rearmost portion of the rear fascia. With the Hollywood Racks Sport Rider SE2 Bike Rack # HR1450Z folded up it has a measurement of 5" from the hitch pin center hole to the nearest part of the rack. So you will be able to use this bike rack with the etrailer receiver on your Hyundai. view full answer...
The lowest priced roof rack option we offer for the 2020 Hyundai Santa Fe with a bare roof would be a round bar rack from Yakima. The rack would consist of the following parts:
• Yakima 48 Inch Round Crossbars, part # Y00408
• Yakima BaseLine Roof Rack Towers, part # Y28TR
• Yakima SL Round Bar Adapters, part # Y03536
• Base Clip Fit Kit # Y06151
• Base Clip Fit Kit # Y06154
Unfortunately, the Malone # MPG215 rack you'd looked at isn't' a fit for your Santa Fe.
I've linked you to an... view full answer...
We installed the CIPA tow mirror part # CM11980 on a 2017 Hyundai Santa Fe and found it fit and worked really well. I attached an install video and picture for more info for you to check out as well.
I wasn't able to find any info on the blind spot sensors of your vehicle but we have not had any reports back that these mirrors interfered with them so I'd be inclined to think there wouldn't be any issue at all. view full answer...
We have the replacement screw you are looking for with the part # Y8880150 which matches up to the nut of the # Y8880279 which is M6. view full answer...
As long as you have a hitch installed on your 2014 Hyundai Santa Fe like the Curt part # C13153 which is rated for weight distribution you'd be fine. This would be a great solution to allow you to tow your weight capacity safer too.
For a weight distribution that would work well we have the part # RP66082 which has a tongue weight range of 200-600 lbs and has the only sway control system on the market that's designed to fight sway before it starts.
For a 2 inch ball you would want part... view full answer...
Instead of using the 5 pole connector, you will need a T-1 Connector, part # 118473. The T-1 connector has a tail light converter that combines the brake and directional signals onto one circuit for the left side of the trailer, and one for the right side.
This will allow you to tow any trailer with a 4-pole connector. view full answer...
Yes, The AirBedz XUV Air Mattress w/ Built-In Battery # 341031 is confirmed to fit well in your 2010 Hyundai Santa Fe.
This mattress will fill the entire cargo area and in between your wheel wells. The built-in pump inflates and deflates your mattress in minutes. The mattress is made out of a durable polyester and is resistant to punctures and leaks along seams. The mattress can hold up to 600 pounds.
I attached a review video link below. view full answer...
It looks like the connector for the tow package on a 2020 Hyundai Santa Fe is hit or miss (more hit than miss) so you may still have it. You'll be looking for a black connector under and behind the driver's side of the bumper (see attached). If you have this connector then the T-Connector # CU94FR will plug in there and you're good to go!
Attached is an installation video on a 2021 Santa Fe for you to check out.
If you don't have this plug then you need the Curt Upgraded Circuit Protected... view full answer...
The Swagman Semi 2.0 Platform Bike Rack, # S64686, would work well with your carbon fiber framed bike. The bike rack uses a wheel hook arm design to secure the bikes to the rack. These hook arms will not be in contact of the frame of your bike.
The Swagman Semi 2.0 can carry a bike with a wheelbase as large as 50 inches and as small as 37 inches. So, if the wheelbase of the kids bike falls in between these numbers, then the bike can be secured to the bike rack.
If the wheelbase of the... view full answer...
We have exactly what you need with the Curt T-Connector # CU94FR. This plugs right into the connector for the factory trailer tow package on your 2020 Hyundai Santa Fe and provides you with a 4-Way flat connector for basic trailer wiring. I have attached an installation video of this kit on a '19 Santa Fe that you can reference.
If you don't already have a trailer hitch, then I recommend the Draw-Tite # 75908 because it has a mounting bracket welded onto the crosstube which pairs nicely... view full answer...
Your custom fit Draw-Tite Max-Frame Trailer Hitch Receiver # 75776 is a confirmed fit for 2013-2015 Hyundai Santa Fe GLS and Limited models as well as 2016-2018 Hyundai Santa Fe SE and Limited. These are the only year and models it is confirmed to fit. view full answer...
It does not matter which bolts you torque down first. Alternating sides will be beneficial because it should make tightening the other bolts easier (so none bind). All the torque specs can be found in the installation instructions which I have linked. I have also included a link to a video showing a typical installation for you. view full answer...
Go To Results